[资料]

TM4C TI PinMux工具使用教程

2018-8-14 06:40:19 4119 TM4C

0 TM4C ti PinMux工具使用教程记得以前TI的TM4C12x是有PinMux这个工具的电脑版的，可以自由的安装和使用，不过现在电脑版被放弃了，主打的是网络版。地址如下所示： https://dev.ti.com/pinmux/app.html#/default 打开后显示如下：首先选择开发板的型号和芯片的名称，由于我是自己的板子，所以直接选择芯片的名称就好了。点击start开始进行设计。打开后的界面如下所示。最左面是所选择的芯片对应的所有外设名称和数量，中间是当前所选择外设的引脚，并列出了可选择或者映射的引脚名称，最右面是芯片的引脚图和可生成的配置文件下载。配置好外设的引脚名称和功能后，点击最右面的下载，即可下载配置好的外设初始化.c和.h文件了。 0
2018-8-14 06:40:19　　评论淘帖0 举报相关推荐 • 在TM4C MCU上使用FreeRTOS开发高级应用 0 • TM4C输出使能问题 1567 • TM4C系列基于ARM Cortex-M4 内核的MCU 66 • TI的TM4C单片机调试资料和相关开发资料分享 1067 • 在TM4C MCU上用FreeRTOS开发通用应用程序应用说明 0 • 基于TM4C主控的匿名拓空者飞控 2539 • TM4C串口不能进入中断 1549 • 请问tm4c如何输出4路有相位差的pwm波 3210 • 请问LM4F120H5QR在和TM4C哪个型号是对应的?? 1398 • 请问TM4C和STM32L4哪个功耗更低？ 2670 2 个讨论

0 生成的代码如下所示: //***************************************************************************//// Configure the device pins for different signals//// Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/ // // // Redistribution and use in source and binary forms, with or without // modification, are permitted provided that the following conditions // are met://// Redistributions of source code must retain the above copyright // notice, this list of conditions and the following disclaimer.//// Redistributions in binary form must reproduce the above copyright// notice, this list of conditions and the following disclaimer in the // documentation and/or other materials provided with the // distribution.//// Neither the name of Texas Instruments Incorporated nor the names of// its contributors may be used to endorse or promote products derived// from this software without specific prior written permission.//// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS // "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT // LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR// A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT // OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, // SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT // LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,// DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY// THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT // (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE // OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.////*************************************************************************// This file was automatically generated on 2018/2/20 at 下午10:45:29// by TI PinMux version 4.0.1511 ////*************************************************************************#include #include #include "inc/hw_gpio.h"#include "inc/hw_memmap.h"#include "inc/hw_types.h"#include "driverlib/gpio.h"#include "driverlib/pin_map.h"#include "driverlib/rom.h"#include "driverlib/rom_map.h"#include "driverlib/sysctl.h"#include "pinout.h"//*************************************************************************////! addtogroup pinout_api//! @[////*************************************************************************//*************************************************************************////! Configures the device pins for the customer specific usage.//!//! return None.////*************************************************************************voidPinoutSet(void)[ // // Enable Peripheral Clocks // MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD); // // Configure the GPIO Pin Mux for PD0 // for GPIO_PD0 // MAP_GPIOPinTypeGPIOOutput(GPIO_PORTD_BASE, GPIO_PIN_0); MAP_GPIOPinWrite(GPIO_PORTD_BASE, GPIO_PIN_0, GPIO_PIN_0); // // Configure the GPIO Pin Mux for PD2 // for GPIO_PD2 // MAP_GPIOPinTypeGPIOInput(GPIO_PORTD_BASE, GPIO_PIN_2); // // Configure the GPIO Pin Mux for PD3 // for GPIO_PD3 // MAP_GPIOPinTypeGPIOInput(GPIO_PORTD_BASE, GPIO_PIN_3); // // Configure the GPIO Pin Mux for PD1 // for GPIO_PD1 // MAP_GPIOPinTypeGPIOInput(GPIO_PORTD_BASE, GPIO_PIN_1);]//*************************************************************************//// Close the Doxygen group.//! @]////*************************************************************************//*************************************************************************// pinout.h//// configure the device pins for different signals//// Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/ // // // Redistribution and use in source and binary forms, with or without // modification, are permitted provided that the following conditions // are met://// Redistributions of source code must retain the above copyright // notice, this list of conditions and the following disclaimer.//// Redistributions in binary form must reproduce the above copyright// notice, this list of conditions and the following disclaimer in the // documentation and/or other materials provided with the // distribution.//// Neither the name of Texas Instruments Incorporated nor the names of// its contributors may be used to endorse or promote products derived// from this software without specific prior written permission.//// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS // "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT // LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR// A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT // OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, // SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT // LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,// DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY// THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT // (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE // OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.////*************************************************************************// This file was automatically generated on 2018/2/20 at 下午10:45:32// by TI PinMux version 4.0.1511 ////*************************************************************************#ifndef __DRIVERS_PINOUT_H__#define __DRIVERS_PINOUT_H__//*************************************************************************//// If building with a C++ compiler, make all of the definitions in this header// have a C binding.////*************************************************************************#ifdef __cplusplusextern "C"[#endif//*************************************************************************//// Prototypes.////*************************************************************************extern void PinoutSet(void);//*************************************************************************//// Mark the end of the C bindings section for C++ compilers.////***************************************************************************#ifdef __cplusplus]#endif#endif // __DRIVERS_PINOUT_H__

2018-8-14 06:51:02 评论举报 1^# 韦明