1
完善资料让更多小伙伴认识你,还能领取20积分哦, 立即完善>
扫一扫,分享给好友
你好,
我在STEVAL-MKI062V2中更新固件时遇到问题。根据手册更新它我必须将板切换到DFU模式,但系统在这种模式下看不到设备。下面我简单地写下了我所做的一些步骤。我检查了Windows 7(x64)和Windows XP SP3。 1.从CD安装整个软件:iNEMO Suit,DfuSe等。 2.通过USB电缆插入设备 3.检查iNEMO Suit是否正常工作。 - 工作得很好。我能够捕获一些数据。 4.尝试从iNEMO Suit选项进入DFU模式。 - 它显示设备已切换到DFU模式的消息,但程序''STDFU Tester''和''DfuSe Demonstration'似乎看不到它。此外,系统设备管理器也看不到它。 5.关闭设备。按住按钮SW2。打开设备。 - 系统显示有关安装失败的信息。 如果有人有类似的问题,我会很感激任何信息。 #dfu #inemo#stevalmki062v2 以上来自于谷歌翻译 以下为原文 Hello, I have problem with updating firmware in STEVAL-MKI062V2. According to manual to update it I have to switch board into DFU mode, but system doesn't see the device in this mode. Below I wrote out in few steps what I did. I checked it for both Windows 7(x64) and Windows XP SP3. 1. Installation of whole software from CD: iNEMO Suit, DfuSe etc. 2. Plug device via u*** cable 3. Check if it works correctly with iNEMO Suit. - It worked fine. I was able to capture some data. 4. Try to go into DFU mode from iNEMO Suit option. - It displays a message that device has been switched into DFU mode, but programs ''STDFU Tester'' and ''DfuSe Demonstration'' seems to not see it. Moreover system Device Manager doesn't see it too. 5. Turn off device. Hold button SW2. Turn on device. - System shows information about installation failure. If someone had similar problem I would be grateful for any information. #dfu #inemo #stevalmki062v2 |
|
相关推荐
1个回答
|
|
一般程序是:
安装最新版本的iNEMO Suite 2.2 http://www.st.com/inemo 。 从“固件升级”套件菜单进入DFU模式,并验证系统将该板识别为“STM32 DFU设备”。 在这种情况下,从DFU images子文件夹中浏览所需的.hex文件并升级固件。如果是在DFU模式下,当没有被识别为''STM32 DFU设备'时,你可能会遇到两个不同的问题: 1)原始DFU固件已损坏,在这种情况下,您需要通过JTAG再次下载 2)驱动程序安装错误,在这种情况下关闭所有应用程序,从控制面板中删除iNEMO套件并重新安装所有应用程序。最好的问候 iNEMOâ“¢团队 以上来自于谷歌翻译 以下为原文 The general procedure is: Install last version of iNEMO Suite 2.2 available at http://www.st.com/inemo . Enter in DFU mode from ''Firmware Upgrade'' Suite's menu, and verify that the system recognize the board as “STM32 DFU deviceâ€�. In this case browse the desiderated .hex file from DFU images sub folder and upgrade the firmware.If the board, when is in DFU mode, don’t is recognized as ''STM32 DFU device'', you may have two different problems: 1) The original DFU firmware was corrupted, in this case you need to download it again via JTAG 2) The driver was bad installed, in this case close all applications, remove from control panel the iNEMO suite and reinstall all again.Best Regards iNEMOâ„¢ Team |
|
|
|
只有小组成员才能发言,加入小组>>
请教:在使用UDE STK时,单片机使用SPC560D30L1,在配置文件怎么设置或选择?里面只有SPC560D40的选项
2732 浏览 1 评论
3241 浏览 1 评论
请问是否有通过UART连接的两个微处理器之间实现双向值交换的方法?
1810 浏览 1 评论
3650 浏览 6 评论
6038 浏览 21 评论
1339浏览 4评论
201浏览 3评论
对H747I-DISCO写程序时将CN2的st-link复用为usart1,再次烧录时无法检测到stlink怎么解决?
350浏览 2评论
STM32G474RE芯片只是串口发个数据就发烫严重是怎么回事?
443浏览 2评论
STM32处理增量式编码器Z信号如何判断中断是正转的还是反向转的?
274浏览 2评论
小黑屋| 手机版| Archiver| 德赢Vwin官网 ( 湘ICP备2023018690号 )
GMT+8, 2024-12-23 18:45 , Processed in 0.970552 second(s), Total 48, Slave 42 queries .
Powered by 德赢Vwin官网 网
© 2015 bbs.elecfans.com
关注我们的微信
下载发烧友APP
德赢Vwin官网 观察
版权所有 © 湖南华秋数字科技有限公司
德赢Vwin官网 (电路图) 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证:合字B2-20210191 工商网监 湘ICP备2023018690号