完善资料让更多小伙伴认识你，还能领取20积分哦， 立即完善>
3天内不再提示
德赢Vwin官网
论坛|
当我测量空中（OTA）信号时，我的所有My Spectrum分析仪N9344C都会显示“过载”信息噪声基底也可能上升并隐藏感兴趣的信号。
即使OTA信号超出当前跨度，也会发生这种情况。 解决方案是使用外部带通滤波器将OTA信号限制到感兴趣的频带。 现在我想选择一个具有宽范围的带通填充器可调谐器（与N9344C相同，DC -20GHz）。 所以没有一个滤波器的范围DC - 20GHz。 请告诉我解决方案。 谢谢 以上来自于谷歌翻译 以下为原文 Hi all My Spectrum analyser N9344C display an “overload” message when I measure Over-the-Air (OTA) signal The noise floor may also rise and hide signals of interest. This can happen even if the OTA signal is outside of the current span. Solution is to use an external band pass filter to limit OTA signals to the band of interest. Now I want to choose one bandpass fillter tunable that had the wide range (the same to N9344C, DC -20GHz). so there aren't one filter that had range DC - 20GHz. Please advise solution for me. Thanks 
0
|
|
相关推荐
10个回答
|
|
|
嗨 - 解决方案是：A。调整频谱分析仪的衰减器值，或使用外部衰减器降低不需要的OTA信号。
B.根据您要测量的实际信号频率和带宽，选择较窄的频段选择器或使用多个选择器（带通滤波器）。 C.找到实际导致频谱分析仪过载的信号，并尝试使用适当的陷波滤波器来消除它对仪器的影响。 我希望这有帮助 - 以上来自于谷歌翻译 以下为原文 Hi - The solution would be: A. Adjust the attenuator value of the spectrum analyzer, or use an external attenuator to lower down the unwanted OTA signal. B. Choose a narrower band selector or to use multiple selectors (bandpass filters) according to the actual signal frequency and bandwidth which you want to measure. C. Find the signal which actually cause the overload of the spectrum analyzer, and try to use a appropriate notch filter to eliminate the impact of it to the instrument. I hope this helps - |
|
|
|
|
|
非常感谢，tabbott我选择解决方案B，但我想限制用于DC-20GHz频率范围的滤波器数量，这意味着我选择的多个选择器（带通滤波器）必须具有宽频率范围。
你能告诉我有最大频率范围的模型滤波器吗？ “B.根据您要测量的实际信号频率和带宽，选择较窄的频段选择器或使用多个选择器（带通滤波器）。” 以上来自于谷歌翻译 以下为原文 Thanks very much, tabbott I choose solution B, but I want to limit the number of filters to use for frequency range DC-20GHz, meaning the multiple selectors (bandpass filters) that i choose must a wide frequency range. Can you advise me model filter that had max frequency range. "B. Choose a narrower band selector or to use multiple selectors (bandpass filters) according to the actual signal frequency and bandwidth which you want to measure." |
|
|
|
|
|
非常感谢，tabbott我选择解决方案B，但我想限制用于DC-20GHz频率范围的滤波器数量，这意味着我选择的多个选择器（带通滤波器）必须具有宽频率范围。
你能告诉我有最大频率范围的模型滤波器吗？ “B.根据您要测量的实际信号频率和带宽，选择较窄的频段选择器或使用多个选择器（带通滤波器）。” 以上来自于谷歌翻译 以下为原文 Thanks very much, tabbott I choose solution B, but I want to limit the number of filters to use for frequency range DC-20GHz, meaning the multiple selectors (bandpass filters) that i choose must a wide frequency range. Can you advise me model filter that had max frequency range. "B. Choose a narrower band selector or to use multiple selectors (bandpass filters) according to the actual signal frequency and bandwidth which you want to measure." |
|
|
|
|
|
非常感谢，tabbott我选择解决方案B，但我想限制用于DC-20GHz频率范围的滤波器数量，这意味着我选择的多个选择器（带通滤波器）必须具有宽频率范围。
你能告诉我有最大频率范围的模型滤波器吗？ “B.根据您要测量的实际信号频率和带宽，选择较窄的频段选择器或使用多个选择器（带通滤波器）。” 以上来自于谷歌翻译 以下为原文 Thanks very much, tabbott I choose solution B, but I want to limit the number of filters to use for frequency range DC-20GHz, meaning the multiple selectors (bandpass filters) that i choose must a wide frequency range. Can you advise me model filter that had max frequency range. "B. Choose a narrower band selector or to use multiple selectors (bandpass filters) according to the actual signal frequency and bandwidth which you want to measure." |
|
|
|
|
|
非常感谢，tabbott我选择解决方案B，但我想限制用于DC-20GHz频率范围的滤波器数量，这意味着我选择的多个选择器（带通滤波器）必须具有宽频率范围。
你能告诉我有最大频率范围的模型滤波器吗？ “B.根据您要测量的实际信号频率和带宽，选择较窄的频段选择器或使用多个选择器（带通滤波器）。” 以上来自于谷歌翻译 以下为原文 Thanks very much, tabbott I choose solution B, but I want to limit the number of filters to use for frequency range DC-20GHz, meaning the multiple selectors (bandpass filters) that i choose must a wide frequency range. Can you advise me model filter that had max frequency range. "B. Choose a narrower band selector or to use multiple selectors (bandpass filters) according to the actual signal frequency and bandwidth which you want to measure." |
|
|
|
|
|
非常感谢，tabbott我选择解决方案B，但我想限制用于DC-20GHz频率范围的滤波器数量，这意味着我选择的多个选择器（带通滤波器）必须具有宽频率范围。
你能告诉我有最大频率范围的模型滤波器吗？ “B.根据您要测量的实际信号频率和带宽，选择较窄的频段选择器或使用多个选择器（带通滤波器）。” 以上来自于谷歌翻译 以下为原文 Thanks very much, tabbott I choose solution B, but I want to limit the number of filters to use for frequency range DC-20GHz, meaning the multiple selectors (bandpass filters) that i choose must a wide frequency range. Can you advise me model filter that had max frequency range. "B. Choose a narrower band selector or to use multiple selectors (bandpass filters) according to the actual signal frequency and bandwidth which you want to measure." |
|
|
|
|
|
非常感谢，tabbott我选择解决方案B，但我想限制用于DC-20GHz频率范围的滤波器数量，这意味着我选择的多个选择器（带通滤波器）必须具有宽频率范围。
你能告诉我有最大频率范围的模型滤波器吗？ 以上来自于谷歌翻译 以下为原文 Thanks very much, tabbott I choose solution B, but I want to limit the number of filters to use for frequency range DC-20GHz, meaning the multiple selectors (bandpass filters) that i choose must a wide frequency range. Can you advise me model filter that had max frequency range. |
|
|
|
|
|
非常感谢，tabbott我选择解决方案B，但我想限制用于DC-20GHz频率范围的滤波器数量，这意味着我选择的多个选择器（带通滤波器）必须具有宽频率范围。
你能告诉我有最大频率范围的模型滤波器吗？ 以上来自于谷歌翻译 以下为原文 Thanks very much, tabbott I choose solution B, but I want to limit the number of filters to use for frequency range DC-20GHz, meaning the multiple selectors (bandpass filters) that i choose must a wide frequency range. Can you advise me model filter that had max frequency range. |
|
|
|
|
|
非常感谢，tabbott我选择解决方案B，但我想限制用于DC-20GHz频率范围的滤波器数量，这意味着我选择的多个选择器（带通滤波器）必须具有宽频率范围。
你能告诉我有最大频率范围的模型滤波器吗？ 以上来自于谷歌翻译 以下为原文 Thanks very much, tabbott I choose solution B, but I want to limit the number of filters to use for frequency range DC-20GHz, meaning the multiple selectors (bandpass filters) that i choose must a wide frequency range. Can you advise me model filter that had max frequency range. |
|
|
|
|
那一年坏坏 发表于 2018-11-26 15:33 我的电脑有问题，抱歉，请删除一些重复的回复 以上来自于谷歌翻译 以下为原文 My computer have a problem, sorry, please delete some repeating reply |
|
|
|
|
只有小组成员才能发言，加入小组>>
1283 浏览 0 评论
2371 浏览 1 评论
2189 浏览 1 评论
2062 浏览 5 评论
2946 浏览 3 评论
1105浏览 1评论
关于Keysight x1149 Boundary Scan Analyzer
752浏览 0评论
N5230C用“CALC:MARK:BWID？”获取Bwid,Cent,Q,Loss失败，请问大佬们怎么解决呀
923浏览 0评论
1285浏览 0评论
/6 
关注我们的微信
下载发烧友APP
德赢Vwin官网 观察
版权所有 © 湖南华秋数字科技有限公司
德赢Vwin官网 （电路图） 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证：合字B2-20210191
工商网监
湘ICP备2023018690号
1734
评论
淘帖
1514
