STM8S003k3 fnd无法正常工作

大家好。我在STM8S105K4T6上有一个可行的pwm代码，现在我把它粘贴到STM8S003k3 fnd它将无法正常工作。


＆amp; sharpdefine CCR1_Val（（u16）2047）//配置通道1脉冲宽度蓝色
＆amp; sharpdefine CCR2_Val（（u16）2047）//配置通道2脉冲宽度

sta tic void TIM1_Config（void）
{


TIM1_DeInit（）;


/ *时基配置* /
/ *
TIM1_Period = 4095
TIM1_Prescaler = 0
TIM1_CounterMode = TIM1_COUNTERMODE_UP
TIM1_RepetitionCounter = 0
* /


TIM1_TimeBaseInit（0，TIM1_COUNTERMODE_UP，4095,0）;


/ *通道1,2,3和4在PWM模式下配置* /

/ *
TIM1_OCMode = TIM1_OCMODE_PWM2
TIM1_OutputState = TIM1_OUTPUTSTATE_ENABLE
TIM1_OutputNState = TIM1_OUTPUTNSTATE_ENABLE
TIM1_Pulse = CCR1_Val
TIM1_OCPolarity = TIM1_OCPOLARITY_LOW
TIM1_OCNPolarity = TIM1_OCNPOLARITY_HIGH
TIM1_OCIdleState = TIM1_OCIDLESTATE_SET
TIM1_OCNIdleState = TIM1_OCIDLESTATE_RESET

* /


/ * TIM1_Pulse = CCR2_Val * /
TIM1_OC2Init（TIM1_OCMODE_PWM2，TIM1_OUTPUTSTATE_ENABLE，TIM1_OUTPUTNSTATE_ENABLE，CCR2_Val，
TIM1_OCPOLARITY_LOW，TIM1_OCNPOLARITY_HIGH，TIM1_OCIDLESTATE_SET，
TIM1_OCNIDLESTATE_RESET）;




/ * TIM1_Pulse = CCR4_Val * /
TIM1_OC4Init（TIM1_OCMODE_PWM2，TIM1_OUTPUTSTATE_ENABLE，CCR1_Val，TIM1_OCPOLARITY_LOW，
TIM1_OCIDLESTATE_SET）;


/ * TIM1计数器启用* /
TIM1_Cmd（ENABLE）;


/ * TIM1主输出使能* /
TIM1_CtrlPWMOutputs（ENABLE）;
}

任何人都可以告诉我这里有什么问题。


＃stm8s003k3-TIM1-PWM-问题



以下为原文




Hello every one. I have a workable code of pwm on STM8S105K4T6 and now I paste it in STM8S003k3 fnd it won't work.


&sharpdefine CCR1_Val ((u16)2047) // Configure channel 1 Pulse Width Blue
&sharpdefine CCR2_Val ((u16)2047) // Configure channel 2 Pulse Width

static void TIM1_Config(void)
{


TIM1_DeInit();


/* Time Base configuration */
/*
TIM1_Period = 4095
TIM1_Prescaler = 0
TIM1_CounterMode = TIM1_COUNTERMODE_UP
TIM1_RepetitionCounter = 0
*/


TIM1_TimeBaseInit(0, TIM1_COUNTERMODE_UP, 4095, 0);


/* Channel 1, 2,3 and 4 Configuration in PWM mode */

/*
TIM1_OCMode = TIM1_OCMODE_PWM2
TIM1_OutputState = TIM1_OUTPUTSTATE_ENABLE
TIM1_OutputNState = TIM1_OUTPUTNSTATE_ENABLE
TIM1_Pulse = CCR1_Val
TIM1_OCPolarity = TIM1_OCPOLARITY_LOW
TIM1_OCNPolarity = TIM1_OCNPOLARITY_HIGH
TIM1_OCIdleState = TIM1_OCIDLESTATE_SET
TIM1_OCNIdleState = TIM1_OCIDLESTATE_RESET

*/


/*TIM1_Pulse = CCR2_Val*/
TIM1_OC2Init(TIM1_OCMODE_PWM2, TIM1_OUTPUTSTATE_ENABLE, TIM1_OUTPUTNSTATE_ENABLE, CCR2_Val,
TIM1_OCPOLARITY_LOW, TIM1_OCNPOLARITY_HIGH, TIM1_OCIDLESTATE_SET,
TIM1_OCNIDLESTATE_RESET);




/*TIM1_Pulse = CCR4_Val*/
TIM1_OC4Init(TIM1_OCMODE_PWM2, TIM1_OUTPUTSTATE_ENABLE, CCR1_Val, TIM1_OCPOLARITY_LOW,
TIM1_OCIDLESTATE_SET);


/* TIM1 counter enable */
TIM1_Cmd(ENABLE);


/* TIM1 Main Output Enable */
TIM1_CtrlPWMOutputs(ENABLE);
}

Can any one tell me what is wrong here.


#stm8s003k3-tim1-pwm-problem