谁知道JTAG装载机电缆组件的来源吗

如果你在谈论直接插入电路板的PC板上的连接器
USB编程器的带状电缆，这是Molex的一部分：
87832-1420
DigiKey带有这些。
在他们的网站上搜索部件号，你会看到它的图片。
这是一个表面安装，但如果你看看Molex网站，我相信你
如果您愿意，可以获得通孔版本。
HTH，
的Gabor
- Gabor



以下为原文

If you're talking about the connector on a PC board that directly plugs into the
ribbon cable of the USB programmer, that's a Molex part:

87832-1420

DigiKey carries these. Search for the part number on their site and you'll see a picture of it.

This one is surface mounted, but if you look at the Molex site I believe you
can get a through-hole version if you prefer.

HTH,
Gabor
-- Gabor

的Gabor，
感谢您的回复，但部件号是针对公连接器的。
我正在寻找PC板安装（SM，notthur hole）极化母配合连接器部件号。



以下为原文

Gabor,

Thanks for the reply but that part number is for the male connector. I'm looking for the PC board mount (SM, not thur hole) polarized female mating connector part number.

hobie346写道：Gabor，
感谢您的回复，但部件号是针对公连接器的。
我正在寻找PC板安装（SM，notthur hole）极化母配合连接器部件号。
板安装连接器是公头。
----------------------------是的，我这样做是为了谋生。



以下为原文

hobie346 wrote:
Gabor,

Thanks for the reply but that part number is for the male connector. I'm looking for the PC board mount (SM, not thur hole) polarized female mating connector part number.

The board-mount connector is male.
----------------------------Yes, I do this for a living.

bassman59，
在某种程度上，你是正确的，除了在这种情况下，PCB组件上有两个连接器。
顶部是一个直角1x9 .100“连接器。底部有一个SM，极化2x7 2mm母连接器。这是我正在寻找零件编号和供应商的连接器。我已经包含了一个类似于
三张照片显示了飞行导线组件。



以下为原文

bassman59,

In part you are correct except in this case there two connectors on the PCB assembly. The top one is a right-angle 1x9 .100" connector. The bottom side has a SM, polarized 2x7 2mm female connector. This is the connector that I'm looking for a part number and supplier. I've included a like to three photos showing the flying lead assembly.

您是否正在尝试构建自己的飞线适配器？
如果是这样我建议
只需使用标准带状电缆，然后使用适配器上的公连接器。
它在整个长度上添加了一条色带，但色带可以很短
每一根电线都是理由。
如果您正在构建自己的连接到程序员的板，则使用功能区
电缆是最好的方式，不需要女性SMT连接器。
问候，
的Gabor
- Gabor



以下为原文

Are you trying to build your own flying lead adapter? If so I'd suggest
just using the standard ribbon cable and then a male connector on your adapter.
It adds a ribbon to the overall length, but the ribbon can be short and there
are grounds on every other wire.

If you're building your own board that connects to the programmer, the ribbon
cable is the best way again, no need for female SMT connectors.

Regards,
Gabor
-- Gabor

PCB到PCB连接的键控插座并不常见，因为PCB通常只采用单向连接，因此这是一个定制部件。
非键控Molex版本为79109-1006。
如果键控对您非常重要，您可以将一个小塑料胶粘在正确的位置。
部件号是Samtec ASP-11526-01，如果你真的想要这个，但你将无法在像Digikey和Mouser这样的经销商处找到它。
------您是否尝试在Google中输入问题？
如果没有，你应该在发布之前。太多结果？
尝试添加网站：www.xilinx.com



以下为原文

Keyed receptacles for PCB-to-PCB connections are not the norm as PCBs usually only go together one way, so this is a custom part.

A non-keyed Molex version is 79109-1006. If keying was really important to you you could glue a small plastic piece in the correct location.

The part number is Samtec ASP-11526-01 if you really want this, but you won't be able to find this at distributors like Digikey and Mouser.


------Have you tried typing your question into Google? If not you should before posting.
Too many results? Try adding site:www.xilinx.com

我正在尝试构建自己的飞线适配器。
问题是我需要十几个适配器，它们将***入和删除多次。
问题是插入目标板上的错误引脚。
一侧将CF装载板与另一侧连接到目标板。
飞线引线侧连接到CF装载板，极化母连接器连接到目标板。
因为向后插入母连接器，我已经有一个适配器板被炸了。
我已经通过在极化引脚所在的位置插入一个高引脚来固定我的样品。
我担心有一个胖手指的人即使有额外的针也会向后插入适配器。
我不是很担心转接板会变质;
这是我担心的目标板 - $ 10K LX330。
吸烟其中一个会让某人失去工作。



以下为原文

I am trying to build my own flying lead adapter. The problem is I need a dozen of the adapter and they are going to be inserted and removed many times. The problem is inserting to a wrong pin on the target board. One side connects a CF loader board and the other to a target board. The flying lead side connects to the CF loader board and the polarized female connector connects to the target board. I've already had one adapter board fried due inserting the female connector backwards. I've fixed my sample by inserting a tall pin where the polarized pin would be. I'm worried that someone with a fat finger is going to insert the adapter backwards even with the extra pin. I'm not so worried about the adapter board getting fried; it's the target board that I'm worried about - $10K LX330. Smoking one of those is going to cost someone their job.

感谢您的信息。
我开始认为这是一个自定义的部分。



以下为原文

Thanks for the information. I was beginning to think this was a custom part.

hobie346写道：我正在尝试建立自己的飞行铅适配器。
问题是我需要十几个适配器，它们将***入和删除多次。
问题是插入目标板上的错误引脚。
一侧将CF装载板与另一侧连接到目标板。
飞线引线侧连接到CF装载板，极化母连接器连接到目标板。
因为向后插入母连接器，我已经有一个适配器板被炸了。
我已经通过在极化引脚所在的位置插入一个高引脚来固定我的样品。
我担心有一个胖手指的人即使有额外的针也会向后插入适配器。
我不是很担心转接板会变质;
这是我担心的目标板 - $ 10K LX330。
吸烟其中一个会让某人失去工作。
那么为什么目标板设计有错误的JTAG连接器呢？
----------------------------是的，我这样做是为了谋生。



以下为原文

hobie346 wrote:
I am trying to build my own flying lead adapter. The problem is I need a dozen of the adapter and they are going to be inserted and removed many times. The problem is inserting to a wrong pin on the target board. One side connects a CF loader board and the other to a target board. The flying lead side connects to the CF loader board and the polarized female connector connects to the target board. I've already had one adapter board fried due inserting the female connector backwards. I've fixed my sample by inserting a tall pin where the polarized pin would be. I'm worried that someone with a fat finger is going to insert the adapter backwards even with the extra pin. I'm not so worried about the adapter board getting fried; it's the target board that I'm worried about - $10K LX330. Smoking one of those is going to cost someone their job.

So why was the target board designed with the wrong sort of JTAG connector?
----------------------------Yes, I do this for a living.

你问错了人。
目标板来自Avnet。
装载板也来自Avent。
我不确定JTAG是不是错误的连接器，因为它与USB平台电缆盒配合得很好。
我将它与Chip Probe Pro s / w一起使用。
我必须断开装载板才能这样做。



以下为原文

You're asking the wrong person. The target board comes from Avnet. The loader board also comes from Avent. I'm not sure the JTAG is the wrong sort of connector or not as it mates with the USB Platform Cable box just fine. I use it with the Chip Probe Pro s/w. I have to disconnect the loader board to do so.

为什么不将SystemACE模块插入Avnet LX330T板上的SAM接头（JP2）？
------您是否尝试在Google中输入问题？
如果没有，你应该在发布之前。太多结果？
尝试添加网站：www.xilinx.com



以下为原文

Why aren't you plugging the SystemACE module in to the SAM header (JP2) on the Avnet LX330T board?------Have you tried typing your question into Google? If not you should before posting.
Too many results? Try adding site:www.xilinx.com

因为我无法让它适应，所以无需拆卸系统即可更换CF卡。



以下为原文

Because there is no way I can get it to fit let along change the CF card without having to dis-assemble the system.

有趣的设置，我现在可以看到你的问题。
有可能使用直角母连接器，使模块垂直定向。
像这部分http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=S5578-ND，但我不确定腿是否足够长。
Avnet开发板用户指南在SAM界面上显示一组垂直连接器，但在更高版本中必须更改为水平版本。
------您是否尝试在Google中输入问题？
如果没有，你应该在发布之前。太多结果？
尝试添加网站：www.xilinx.com



以下为原文

Interesting setup and I can see your problem now.

There is a possibility that a right angle female connector could be used so that the module is oriented vertically. Something like this part http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=S5578-ND but I'm not sure if the legs will be long enough.

The Avnet board user guide shows a vertical set of connectors on the SAM interface, but this must have been changed to the horizontal version on a later version.
------Have you tried typing your question into Google? If not you should before posting.
Too many results? Try adding site:www.xilinx.com

不，你是对的;
那里有一个垂直的标题，但我们不得不改变前一个项目的直角到期清除问题。



以下为原文

No you are correct; there was a vertical header there but we had to change to right-angle due clearance problems on a previous project.