PSoC Creator 2.0有什么问题？

你好，
谢谢你帮我的忙。我刚刚复习过：
使用CY8C5688 AX*- 60 ES1（这就是MixPro 3所说的）
我在创建2的修订文档中红了：ES1不再支持。
可能是错误。如果你能用ES1获得PSOC5处理器模块，你可以试试。
对于模块当前没有ESE交换程序吗？（我住在德国，怎么办？）？？）
问候，鲍伯



以下为原文
Hi,
thanx for your effort to help me. I just reviewed:
Using a CY8C5588AX*-60 ES1 (That's what the Miniprog 3 says)
And I red in the Revision Doc for Creator 2: ES1 no longer supported.
Might be the error. If you can get hands on a PSoC5 processor module with ES1 you can try.
Isn't there an exchange-program to current ESes for the modules? (I reside in Germany, how to???)
Regards, Bob

创建者2的迁移文档明确说明CY8C5688 AXI-060 ES1仍然支持，因为它被交付给客户。



以下为原文
The migration document for Creator 2.0 explicitely states that CY8C5588AXI-060 ES1 is still supported, since it was delivered to customers.

好了，现在我们知道的和以前一样多了。我将安装一个Vista机器上的创建者2，它与一个MixPrim3到一个工具包01a，其中一个工作（测试了CyReal1）PSOC5处理器模块，上面有AsNI1 5588。我会写一个小演示项目，我会告诉你结果。
快乐升级
鲍勃



以下为原文
Ok, so now we know as much as before. I'll install creator 2 on a Vista machine which is connected with a Miniprog3 to a Kit 001a with a working (tested with Creator1) PSoC5 processor module with an ES1 5588 on it. I'll write a small demo project and I'll inform you about the results...
Happy Upgrading
Bob

是的，错误仍然存在，太糟糕了。
错误消息：
警告：不能设置断点：'C:CyPress 另一个测试区域CR2TestCR2Test.CysN\Meal.C：26’。遇到错误（在目标中没有硬件断点支持）。错误：dg.M90015：调试器在运行期间意外退出。遇到错误（远程通信错误：无错误）。
为了清晰起见，我包含了ReBPONT错误消息，调试器也在没有断点的情况下退出。
项目追加。环境：
赢景
PSoC Creator 2
小型机器人3
KIT 01A
CY8C5688 ES1处理器模块
类似项目在同一环境下与PSoC创建者1 SP2协同工作
快乐周末
鲍勃
CR2Test.CyWrk.CaseV01.Zip
913.1 K



以下为原文
Yes, the error persists, too bad.
Errormessage:
Warning: Cannot set breakpoint: 'C:CypressAnother TestareaCr2TestCr2Test.cydsnmain.c:26'. Encountered error (No hardware breakpoint support in the target.).
Error: dbg.M0015: Debugger exited unexpectedly during run. Encountered error (Remote communication error: No error.)

I included the Breakpont-errormessage only for clarity, the debugger exits without a breakpoint as well.
Project appended.
Environment:
Win Vista
PSoC Creator 2
Miniprog 3
Kit 001a
Cy8c5588 ES1 - Processor module
Similar project works fine with PSoC Creator 1 SP2 under the very same environment
Happy weekend
Bob

• Cr2Test.cywrk.Archive01.zip913.1 K
  
  

你能检查MixPrim3时钟速度值吗？选择的速度不应超过目标设备的总线时钟速度的1/3倍，而较慢的速度是可能调试的，速度至少应该是1 MHz来编程设备。6兆赫是最高推荐时钟速度。



以下为原文
Can you check the Miniprog3 clock speed value? The selected speed should not be more than 1/3 rd the value of Bus clock speed of the target device. While slower speeds are possible for debugging, the speed should be at least 1 MHz to program the device. 6 MHz is the highest recommended clock speed.

你好，
我也有调试与PSoC Creator 2问题。同样的消息出现：“dg.M90015：调试器在运行期间意外退出。遇到错误（远程通信错误：没有错误。）”。我已经改变了调试速度（低于1/3 BuxLCK），并且仍然。
我用cy8c3866axi-040es2与cy8ckit-001。该装置适当程序但当您尝试更改为调试模式，错误被。
有什么想法吗？谢谢。



以下为原文
Hello,
I'm also having debug problems with PSoC Creator 2.0. The same message appears: "dbg.M0015: Debugger exited unexpectedly during run. Encountered error (Remote communication error: No error.)". I've changed the Debug speed (lower than 1/3 BUS_CLK) and still.
I am using the CY8C3866AXI-040ES2 with the CY8CKIT-001. The device is properly programed but when you try to change to debug mode, the error apears.
Any ideas? Thank's.

我为我解决了这个问题。
您的Windows用户名不包含任何特殊字符（非ASCII）？我的用户名是“jo rg”。当我安装了一个新的úSER（重命名工作不小心：）一切都好。真的花了我几个小时！
鲍勃



以下为原文
I solved the problem for me.
Does your windows-username contain any special (non ASCII) characters? My username was "Jörg". when I installed a new úser (caution:renaming does NOT work) everything went fine. That did cost me hours, indeed!

Bob