1
完善资料让更多小伙伴认识你,还能领取20积分哦, 立即完善>
大家好,我一直在使用8257D PSG模拟信号发生器(250 kHz-40GHz)。
我想询问SG,它已准备好在发送命令“RF ON”后输出正确的RF信号功率。 我认为应该有一个状态寄存器来查询。 我在编程手册中查找了状态字节,但我找不到。 任何帮助将不胜感激.RegardsCengiz EKEN 以上来自于谷歌翻译 以下为原文 Hi All, I have been using 8257D PSG Analog Signal Generator(250 kHz-40GHz). I want to query the SG that it is ready to output the correct RF Signal Power after sending command "RF ON". I thought there should be a status register for this to be queried. I looked up the status bytes in the programming manual but I could not find. Any help would be appreciated. Regards Cengiz EKEN |
|
相关推荐
2个回答
|
|
Hi Cengiz-E8257D标准事件状态组寄存器位0设置为1时表示命令的最后一个操作已完成。使用以下命令查询该寄存器:* ESR该寄存器的输出是寄存器位的十进制值设置为1
如果只将位0设置为1,则输出为十进制1.如果位2(查询错误)设置为1,则输出十进制4(或者可以设置为1的所有位的十进制和)。 此信息在Agilent Technologies信号发生器编程指南N5180-90005,2009年1月第167页上.http://cp.literature.agilent.com/litweb ... -90005.pdf E8257D标准操作状态组寄存器位1置1时 到1表示信号发生器已经稳定到命令的最后一个状态。使用以下命令查询该寄存器:STATus:OPERation:CONDition?如果位1已设置为1,则小数值输出将为2(或小数和 所有位可以设置为1)。此信息也在Agilent Techn的第167页上 信号发生器编程指南N5180 - 90005,2009年1月.http://cp.literature.agilent.com/litweb ... -90005.pdf第168到172页有关于注册信息的更多细节。我希望这有用 - 以上来自于谷歌翻译 以下为原文 Hi Cengiz - The E8257D Standard Events Status Group register bit 0 when set to a 1 signifies that the last operation commanded has been done. Query this register with the command: *ESR The output of this register is the decimal value of register bits set to 1. If only bit 0 is set to a 1 then the output is decimal 1. If bit 2 (Query Error) is set to 1 then it would output decimal 4 (or the decimal sum of all bits that may be set to 1). This information is on page 167 of the Agilent Technologies Signal Generators Programming GuideN5180-90005, January 2009. http://cp.literature.agilent.com/litweb ... -90005.pdf The E8257D Standard Operation Status Group register bit 1 when set to a 1 signifies the signal generator has settled to the last state commanded. Query this register with the command: STATus:OPERation:CONDition? If bit 1 has been set to a 1 then the decimal value output will be 2 (or the decimal sum of all bits that may be set to 1). This information is also on page 167 of the Agilent Technologies Signal Generators Programming GuideN5180-90005, January 2009. http://cp.literature.agilent.com/litweb ... -90005.pdf Pages 168 through 172 have more detail on register information. I hope this was helpful - |
|
|
|
感谢您的答复。
这真的很有帮助。 我将写一个关于你的答案的小应用程序.RegardsCengiz EKEN 以上来自于谷歌翻译 以下为原文 Thank you for your response. It was really helpful. I am going to write a small application regarding your answer. Regards Cengiz EKEN |
|
|
|
只有小组成员才能发言,加入小组>>
1285 浏览 0 评论
2373 浏览 1 评论
2192 浏览 1 评论
2064 浏览 5 评论
2948 浏览 3 评论
1108浏览 1评论
关于Keysight x1149 Boundary Scan Analyzer
752浏览 0评论
N5230C用“CALC:MARK:BWID?”获取Bwid,Cent,Q,Loss失败,请问大佬们怎么解决呀
924浏览 0评论
1287浏览 0评论
小黑屋| 手机版| Archiver| 德赢Vwin官网 ( 湘ICP备2023018690号 )
GMT+8, 2024-12-23 13:46 , Processed in 1.352869 second(s), Total 80, Slave 64 queries .
Powered by 德赢Vwin官网 网
© 2015 bbs.elecfans.com
关注我们的微信
下载发烧友APP
德赢Vwin官网 观察
版权所有 © 湖南华秋数字科技有限公司
德赢Vwin官网 (电路图) 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证:合字B2-20210191 工商网监 湘ICP备2023018690号