RN4020通讯正确的顺序是什么

Hyoi使用下面的代码启动COMS：这会从RN4020模块产生一个“CMD”响应。



以下为原文

Hi hlao

I use the following code to initiate coms:
BT_Wake_HW = 0;
Delay(2);
BT_Wake_HW = 1; // Wake up Bluetooth module HW

BT_Wake_SW = 0;
Delay(2);
BT_Wake_SW = 1; // Wake up Bluetooth module UART

BT_CMD = 0; // Set to Command mode

This generates a 'CMD' response from the RN4020 module.

Regards
Søren

谢谢你的回复。我还是有点困惑的文件：Wakysw是用来控制运行状态的RN4020。当WAKEKSWW设置为高时，模块唤醒并被设置为活动模式。唤醒后，“CMD”将输出到UART，并指示模块处于命令模式并准备从UART获取命令。相反，当WAKEYSW被设置为低时，MMODULE通过输出“结束”到UART退出命令模式，然后运行IDEP休眠模式。除非UART波特率为2400 BPS，否则UART接口将不会在深度睡眠模式下响应。当模块处于深度休眠模式时，MLDPYEV（引脚11）将被保持低。CMD/MLDP（PIN 8）被用于控制MLDP串行数据服务（参见2.3.7）Microchip MLDP命令“”时的RN4020模块。一旦通过设置CMD/MLDP高来输入MLDPmode，从UART的所有数据作为数据流被发送到对等设备。为了退出MLDP模式，必须将CMD/MLDP设置为低电平，通过将“CMD”输出到UART，RN4020模块返回到命令模式。设置WAKEYHW（PIN 15）从休眠模式唤醒RN4020模块。然后低，然后再被视为一个周期，在前五秒，RN4020模块执行工厂复位。当工厂重置完成时，IFWAKEK-SW很高，工厂重置完成；否则，它是部分工厂重置，保留设备名、私有服务和脚本。请参阅第2.3.1节“SET/GET命令”以了解“SF，1”描述工厂缺省的信息。如何安全地将其放入CMD然后MLDP并再次返回，而不必担心“休眠模式”？



以下为原文

Thank you for your response. I am still a bit confused as for the document:
WAKE_SW is used to control the operating state of the RN4020. When WAKE_SW is
set high, the module wakes up and is set into Active mode. Upon waking up, “CMD”
will be output to the UART and indicate that the module is in Command mode and
ready to take commands from UART. Conversely, when WAKE_SW is set low, the
module exits Command mode by outputting “END” to the UART, and then operates in
Deep Sleep mode. The UART interface will not be responsive in Deep Sleep mode
unless the UART baud rate is 2400 bps. When the module is in Deep Sleep mode,
MLDP_EV (pin 11) will be held low.
CMD/MLDP (pin 8) is used to control the RN4020 module when an MLDP serial data
service (see Section 2.3.7 “Microchip MLDP Commands”) is used. Once MLDP
mode is entered by setting CMD/MLDP high, all data from the UART is sent to the
peer device as a data stream. To exit MLDP mode, CMD/MLDP must be set low so
that the RN4020 module is returned to Command mode by outputting “CMD” to the
UART.
Setting WAKE_HW (pin 15) high wakes the RN4020 module from Dormant mode.
After powering up, if WAKE_HW flips up and down three cycles (putting the
WAKE_HW pin into high, and then low, and then high again is considered one flip
cycle) in the first five seconds, the RN4020 module performs a factory Reset. If
WAKE_SW is high when a factory Reset is performed, the factory Reset is complete;
otherwise, it is a partial factory Reset that retains the device name, private service,
and scripts. Refer to Section 2.3.1 “Set/Get Commands” for information on “SF,1”
describing factory default.


How do I safely put it into cmd then MLDP and back again without the fear of "dormant mode"?

在我准备进入命令模式之前，有什么特别的事情需要在RN4020上做吗？



以下为原文

Does anything special need to be done on power-up to the RN4020 before I am ready to go into command mode?

我直接向RN4020发送配置命令-记住寻找回复或等待。重新启动命令需要一点耐心，因为我的RN4020S需要1200到1300毫秒重新启动。



以下为原文

I go directly to sending configuration commands to the RN4020 - Remember to look for the reply or wait.
The reboot command requires a bit of patience as my RN4020s takes 1200-1300 ms to reboot.

BT_CMD = 0; // Set to Command mode

Delay(4);

memcpy(CommandBuffer,"SF,1n",5); // SF - Command -> Factory reset
cnt = 0;
while (cnt < 5)
{
DRV_USART2_WriteByte(CommandBuffer[cnt]); //
while (U3STAbits.UTXBF) // Wait for buffer to empty
{
}
cnt++; // Next byte
}

Delay(100);

memcpy(CommandBuffer,"SR,00000000n",12); // SR - Command -> Set Roles

你如何写你的手机应用程序发送数据与MLDP模式打开？我没有看到任何开始的例子，有没有一个应用笔记来显示细节？



以下为原文

How do you write your phone app to send out the data with the MLDP mode turned on? I don't see any examples of getting that started, is there an app note to show the details?