[问答]

ANT1M24LR16E没有响应我的I2C命令

问答对人有帮助，内容完整，我也想知道答案 0 我的ANT1M24LR16E似乎没有响应我的I2C命令。在Send7bitAddress之后，它以NACK（一个SCL时钟上的SDA为高电平）响应。这是我第一次写信。为什么它不起作用的任何想法？＃STM32L-m24lr16e-I2C 以上来自于谷歌翻译以下为原文 My ANT1M24LR16E does not seem to repond to my I2C commands. After the Send7bitAddress it reponds with a NACK (SDA high on one SCL clock). This is the first time I'm writing to it. Any ideas on why it is not working? /* Turn on M24LR16E / GPIO_HIGH(GPIOD, GPIO_Pin_2); Delay(100); //x10ms / Generate start condition / I2C_GenerateSTART(I2C1, ENABLE); while (!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_MODE_SELECT)){} //Wait until bus is free / Send device select+read/write cmd and wait for ACK / I2C_Send7bitAddress(I2C1, 0xA6, I2C_Direction_Transmitter); //0xA6 = 0b10100110. Page 18 datasheet while (!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED)){} / Send address byte. Wait until data has been received / I2C_SendData(I2C1, 0x00); //Register while (!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_BYTE_TRANSMITTED)){} I2C_SendData(I2C1, 0x2A); // Data to be written while (!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_BYTE_TRANSMITTED)){} / Generate Stop condition / I2C_GenerateSTOP(I2C1, ENABLE); Delay(100); while (1){} / Shut down M24LR16E */ //GPIO_LOW(GPIOD, GPIO_Pin_2); //Delay(100); #stm32l-m24lr16e-i2c 0
2019-7-16 14:52:52　　评论淘帖0 邀请回答您可以邀请以下用户，快速回答问题 × wang21cj 该类别下有 44 个回答。邀请回答新星之火12138 该类别下有 41 个回答。邀请回答 chm5 该类别下有 39 个回答。邀请回答 hgimtk 该类别下有 33 个回答。邀请回答 HengDu 该类别下有 30 个回答。邀请回答 hwp0415229 该类别下有 28 个回答。邀请回答 jghgfdssas 该类别下有 28 个回答。邀请回答可口可甜该类别下有 26 个回答。邀请回答 kingnet6688 该类别下有 26 个回答。邀请回答颜刚YanG 该类别下有 26 个回答。邀请回答 zyh34997 该类别下有 25 个回答。邀请回答柱子图宁该类别下有 25 个回答。邀请回答 jenny042 该类别下有 25 个回答。邀请回答 kingnet9999 该类别下有 25 个回答。邀请回答 andyfly7 该类别下有 25 个回答。邀请回答麻酱该类别下有 25 个回答。邀请回答 gXDhn 该类别下有 24 个回答。邀请回答 jiangwenwen 该类别下有 24 个回答。邀请回答哼小曲该类别下有 24 个回答。邀请回答云汉007 该类别下有 24 个回答。邀请回答举报郝汉相关推荐 • M24LR16E-R在I2C模式下具有块安全性 1109 • M24LR64E使用I2C读写不起作用 2071 • 启用M24LR16E-R能量收集器 2187 • M24LR16E-R双EEPROM信息可能互相作用吗？ 1516 • 可以使用M24LR04E发送NDEF消息吗？ 986 • Reader Application M24LR04E和Reader Application M24LR16E在数据读取方面有什么区别？ 2050 • 请问怎么获得M24LR64的系统信息？ 1185 • 为什么无法使用M24LR04e上的I2C更改扇区安全状态？ 167 • 如何才能让M24LR16E与智能手机兼容 2997 • M24LR板怎么重新编程？ 1479 1个回答

答案对人有帮助，有参考价值 0 你好 I2C_Send7bitAddress（I2C1 ,, I2C_Direction_Transmitter）; - ＆GT;对于STM32L i2c库（保持库，请使用Cube库），7位格式的I2C_Address字节（0xA6）必须写入0x93（移位1位@右）。这就是设备不对设备选择请求进行确认的原因。另外，阅读你的代码，''有一个错误发送地址字节 ''代码的一部分：M24LR有2个地址字节。为了帮助您完成程序，这是附加文件，是STM32L的I2C代码示例。但请再次使用CUBE平台，更易于编译和使用。最好的祝福 ST NFC客户支持我的ANT1M24LR16E似乎没有响应我的I2C命令。在Send7bitAddress之后，它以NACK（一个SCL时钟上的SDA为高电平）响应。这是我第一次写信。为什么它不起作用的任何想法？以上来自于谷歌翻译以下为原文 Hello I2C_Send7bitAddress(I2C1, , I2C_Direction_Transmitter); -> for STM32L i2c library (Hold library, please use Cube library), the 7bit format I2C_Address byte (0xA6 ) has to be written 0x93 (shift 1 bit @ right). This is the reason why the device doesn't ACK to Device Select request. In addition, reading your code, there is a mistake on '' Send address byte '' part of your code : the M24LR has 2 address bytes. To help you to complete your program, this is in attached file, ,an example of I2C code for STM32L. But again, please, uses CUBE platform, easier to compile and use. Best regards ST NFC customer support My ANT1M24LR16E does not seem to repond to my I2C commands. After the Send7bitAddress it reponds with a NACK (SDA high on one SCL clock). This is the first time I'm writing to it. Any ideas on why it is not working? /* Turn on M24LR16E / GPIO_HIGH(GPIOD, GPIO_Pin_2); Delay(100); //x10ms / Generate start condition / I2C_GenerateSTART(I2C1, ENABLE); while (!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_MODE_SELECT)){} //Wait until bus is free / Send device select+read/write cmd and wait for ACK / I2C_Send7bitAddress(I2C1, 0xA6, I2C_Direction_Transmitter); //0xA6 = 0b10100110. Page 18 datasheet while (!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED)){} / Send address byte. Wait until data has been received / I2C_SendData(I2C1, 0x00); //Register while (!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_BYTE_TRANSMITTED)){} I2C_SendData(I2C1, 0x2A); // Data to be written while (!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_BYTE_TRANSMITTED)){} / Generate Stop condition / I2C_GenerateSTOP(I2C1, ENABLE); Delay(100); while (1){} / Shut down M24LR16E */ //GPIO_LOW(GPIOD, GPIO_Pin_2); //Delay(100);

2019-7-16 15:08:39 评论举报吴珺