[问答]

如何使用信号室建立脉冲连接到N8241A？

问答对人有帮助，内容完整，我也想知道答案 0 嗨，我正在尝试使用Signal Studio进行脉冲构建，以连接到N8241A宽带Arb和E8267D矢量信号发生器。使用系统配置向导，我可以连接到E8267D ok了，但是当我尝试连接到N8241A，它使用命令“TCPIP0 :: 192.168.1.101 :: 4000 :: SOCKET”，这将失败。当我使用Agilent Connection Expert时，我可以很好地连接到N8241A，因为它使用命令“TCPIP0 :: 192.168.1.101 :: inst0 :: INSTR”。在系统CONFIGRATION向导，我试图选择“从IO库配置的接口列表中选择一个外部宽带任意波”，我可以看到选择“TCPIP0 :: 192.168.1.101 :: inst0 :: INSTR”，但脉冲大厦去前进并发出命令“TCPIP0 :: 192.168.1.101 :: 4000 :: SOCKET”无论如何。我正在使用Pulse Building版本1.2.28（我也尝试过1.3.25）和Agilent IO Libraries版本15.0。我试过没有运气就卸载并重新安装所有相关的软件。奇怪的是，这个相同的配置适用于另外两台笔记本电脑。在这种情况下，该软件几年前就安装了。我不明白是什么迫使Pulse Building发出“SOCKET”命令，或者我如何改变它。任何帮助都表示赞赏。谢谢，迈克以上来自于谷歌翻译以下为原文 Hi, I am trying to use Signal Studio for Pulse Building to connect to the N8241A Wideband Arb and E8267D Vector Signal Generator. Using the System Configuration Wizard, I can connect to the E8267D ok, but when I try to connect to the N8241A, it uses the command "TCPIP0::192.168.1.101::4000::SOCKET", which fails. When I use the Agilent Connection Expert, I can connect to the N8241A just fine, because it uses the command "TCPIP0::192.168.1.101::inst0::INSTR". In the System Configration Wizard, I tried to select "Choose an External Wideband Arb from list of configured interfaces in IO libraries", I can see the selection "TCPIP0::192.168.1.101::inst0::INSTR", but Pulse Building goes ahead and issues the command "TCPIP0::192.168.1.101::4000::SOCKET" anyway. I am using Pulse Building version 1.2.28 (I have also tried 1.3.25), and Agilent IO Libraries version 15.0. I have tried uninstalling and reinstalling all relevant software without luck. The strange thing is that this same configuration works on two other laptops. In this case, the software was installed several years ago. I don't understand what is forcing Pulse Building to issue the "SOCKET" command, or how I can change it. Any assistance appreciated. Thanks, Mike 0
2019-8-2 14:17:04　　评论淘帖0 邀请回答您可以邀请以下用户，快速回答问题 × kingnet_52040 该类别下有 195 个回答。邀请回答 60user7 该类别下有 81 个回答。邀请回答蓝色冰汐该类别下有 45 个回答。邀请回答醉狼工作室该类别下有 41 个回答。邀请回答 ianwhoani 该类别下有 30 个回答。邀请回答 dkhwakd 该类别下有 25 个回答。邀请回答 aaabbb567 该类别下有 23 个回答。邀请回答 e08506806 该类别下有 20 个回答。邀请回答 szzjfyp 该类别下有 18 个回答。邀请回答 ningee 该类别下有 16 个回答。邀请回答 sonia87 该类别下有 16 个回答。邀请回答 zouqinxiang 该类别下有 15 个回答。邀请回答 xj5548 该类别下有 15 个回答。邀请回答 derek88 该类别下有 14 个回答。邀请回答 daichuangs 该类别下有 14 个回答。邀请回答 hzmbs2016 该类别下有 12 个回答。邀请回答 JST2006 该类别下有 12 个回答。邀请回答 fichesw 该类别下有 11 个回答。邀请回答 www037 该类别下有 11 个回答。邀请回答 ToGoodSoft 该类别下有 11 个回答。邀请回答举报邢钊楚相关推荐 • N8241A加载信号的频谱是错误的 1166 • 连接到N8241A Via Lan收到超时错误 2666 • N8241A AWG如何创建与设备一起使用的bin文件 2464 • 为什么无法连接到N9310A？ 1668 • 8241A仪器驱动程序缺乏编写.pbp文件的能力 1339 • 让ESP32-S3-WROOM-1-N16R2连接到USB时报错如何解决？ 166 • EOS信号应该连接到什么位置？ 2092 • 局域网仪器连接故障 1016 • 如何在9254A中设置保存数据的起点 1227 • 如果设计将单端时钟连接到N侧有什么意义？ 6085 1个回答

答案对人有帮助，有参考价值 0 嗨Mike - 这通常发生在IVI-Compliance软件包和/或N8241A控制实用程序未正确加载时。请访问以下站点并安装最新的IVI-Compliance软件包：http：//search.ni.com/nisearch / app / main / ... ompliance /然后转到以下站点并安装N8241A控制实用程序版本1.31.3：http：//www.home.agilent.com/agilent/edi ... id = 1670471安装后两者以上使用N8241A控制实用程序连接到N8241A。一旦成功，关闭N8142A控制实用程序并打开N7620A并照常连接。注意 - 相关产品：＃N7620A，N8241A，E8267D＃以上来自于谷歌翻译以下为原文 Hi Mike - This usually happens when the IVI-Compliance package and/or the N8241A control utility is not loaded properly. Please go to the following site and install the latest IVI-Compliance package: http://search.ni.com/nisearch/app/main/ ... ompliance/ Then go to the following site and install the N8241A control utility version 1.31.3: http://www.home.agilent.com/agilent/edi ... id=1670471 After installing both of the above use the N8241A control utility to connect to the N8241A. Once this is successful close the N8142A control utility and open the N7620A and connect as usual. Regards - Relevant Products:#N7620A,N8241A,E8267D#

2019-8-2 14:31:55 评论举报李欢