[问答]

ESP32-C3 light-sleep如何实现30ua低功耗？

问答对人有帮助，内容完整，我也想知道答案 0 我司准备用esp32-c3的芯片做主控来开发一tracker类的产品，其中功耗是关键参数，应用场景是蓝牙与手机保持连接、wifi作辅助定位。目前我们买了两块开发板：ESP32-C3-DevKitM-1,想在次开发板上测试一下在蓝牙保持连接的情况下的功耗。阅读文档，要满足我们的需求，需要ble进入light-sleep模式，根据文档我们做了如下修改： 1.在开发板的GPIO0GPIO1两个引脚上加入了外部32K的晶振,如附图所示: 2.已示例程序为基础：ESP_IDFexamplesbluetoothbluedroidblegatt_server_service_table, (1):Enable Power Management: menuconfig ---> Component config ---> Power management ---> Support for power management (2):Enable tickless Idle: menuconfig ---> Component config ---> FreeRTOS ---> Tickless idle support (3) Minimum number of ticks to enter sleep mode for (NEW) Note: Tickless idle needs to be enabled to allow automatic light sleep. FreeRTOS will enter light sleep if no tasks need to run for 3(by default) ticks, that is 30ms if tick rate is 100Hz. Configure the FreeRTOS tick rate to be higher if you want to allow shorter duration light sleep, for example: menuconfig ---> Component config ---> FreeRTOS -> (1000) Tick rate (Hz) (3):Configure external 32.768Hz crystal as RTC clock source: menuconfig ---> Component config ---> ESP32-specific ---> RTC clock source (External 32kHz crystal) Additional current for external 32kHz crystal Note that the "additional current" option is a workaround for a hardware issue on ESP32 that the crystal can fail in oscillating. Please enable this option when you use external 32kHz crystal. This hardware issue will be resolved in the next ECO chip. (4):Enable Bluetooth modem sleep with external 32.768kHz crystal as low power clock: menuconfig ---> Component config ---> Bluetooth ---> Bluetooth controller ---> MODEM SLEEP Options ---> Bluetooth modem sleep Bluetooth Modem sleep mode (ORIG mode(sleep with low power clock)) Bluetooth low power clock (External 32kHz crystal) 并在应用中增加了如下接口代码Code: Select all #include "esp_err.h" #include "esp_pm.h" esp_pm_config_esp32_t pm_config = { .max_freq_mhz = 80, // e.g. 80, 160, 240 .min_freq_mhz = 10, // e.g. 40 .light_sleep_enable = true, // enable light sleep }; ESP_ERROR_CHECK( esp_pm_configure(&pm_config) ); 将程序烧录至开发版，用手机APP连接开发板蓝牙后，测得最小电流为700ua,最大电流为1.2ma,在这之间不断跳动。另外有如下几个参数也在原有的example上做了修改： Code: Select all static esp_ble_adv_params_t adv_params = { .adv_int_min =0x640, .adv_int_max = 0x640, .adv_type = ADV_TYPE_IND, .own_addr_type = BLE_ADDR_TYPE_PUBLIC, .channel_map = ADV_CHNL_ALL, .adv_filter_policy = ADV_FILTER_ALLOW_SCAN_ANY_CON_ANY, }; Code: Select all conn_params.latency = 0; conn_params.max_int = 0x300; // max_int = 0x201.25ms = 40ms conn_params.min_int = 0x10; // min_int = 0x101.25ms = 20ms conn_params.timeout = 400; // timeout = 400*10ms = 4000ms //start sent the update connection parameters to the peer device. esp_ble_gap_update_conn_params(&conn_params); 我的问题是如何使light-sleep 的功耗达到你们文档所说的130ua。使用的ESP_IDF版本是：V4.3 0
2023-2-20 07:12:05　　评论淘帖0 邀请回答您可以邀请以下用户，快速回答问题 × wang21cj 该类别下有 38 个回答。邀请回答 hgimtk 该类别下有 38 个回答。邀请回答新星之火12138 该类别下有 33 个回答。邀请回答 chm5 该类别下有 32 个回答。邀请回答 zyh34997 该类别下有 32 个回答。邀请回答就好国dd 该类别下有 32 个回答。邀请回答 zaichenxi 该类别下有 31 个回答。邀请回答 heks 该类别下有 31 个回答。邀请回答四川赵赵该类别下有 29 个回答。邀请回答 flowerddd 该类别下有 29 个回答。邀请回答 muwersddg 该类别下有 29 个回答。邀请回答 caosurround 该类别下有 28 个回答。邀请回答星星公交站该类别下有 28 个回答。邀请回答 vinww特烦恼该类别下有 28 个回答。邀请回答 lkjflksjfsa 该类别下有 27 个回答。邀请回答 h1654155143.8331 该类别下有 27 个回答。邀请回答 723662364d 该类别下有 27 个回答。邀请回答 overheat 该类别下有 27 个回答。邀请回答 gvjhvbc 该类别下有 27 个回答。邀请回答安德森大该类别下有 27 个回答。邀请回答举报 fansz 相关推荐 • ESP32-C3 Light Sleep功耗与手册Light Sleep的100uA差别有点大如何解决？ 251 • ESP32-C3 light-sleep模式功耗问题求解 217 • ESP32S3有没有方法完全关闭light-sleep？ 180 • esp32-c3进入light-sleep模式后，用按键来唤醒，长时间睡眠用按键就唤醒不了怎么解决？ 364 • 请问大佬们有什么办法能使ESP32-C3进入睡眠状态后BLE依然连接呢？ 174 • ESP32-C3轻度休眠时序问题求解 319 • ESP32-C3-Devkit-M1的功耗问题求解 264 • 能否用内部RTC作为modem sleep低功耗的时钟？ 185 • 能否用内部RTC作为modem sleep低功耗的时钟？ 184 • 在esp32c3-min-1芯片上添加了外设基础上能否做到light-sleep？？ 190