NodeMCU未连接到SinricPro是怎么回事？

大家好，
我想用 esp8266 构建一个恒温器，并通过 Sinricpro 将其连接到 Alexa。我必须说我对 Sinricpro 代码不是很有经验和实践；目前我只从 Github 库“esp8266-esp32-sdk-master”中获取了名为 Thermostat.ino 的示例程序。
我已经输入了 Wi-Fi 和 Sinricpro 连接的所有数据，但目前它连接到互联网（我有串行反馈）但没有连接到 Sinricpro，而且它的网站也处于离线状态。
你有什么建议吗？
谢谢
_ 我附上实用代码
代码： 全选/*
* Example for how to use Lock device as garage door opener
*
* If you encounter any issues:
* - check the readme.md at https://github.com/sinricpro/esp8266-esp32-sdk/blob/master/README.md
* - ensure all dependent libraries are installed
* - see https://github.com/sinricpro/esp8266-esp32-sdk/blob/master/README.md#arduinoide
* - see https://github.com/sinricpro/esp8266-esp32-sdk/blob/master/README.md#dependencies
* - open serial monitor and check whats happening
* - check full user documenta tion at https://sinricpro.github.io/esp8266-esp32-sdk
* - visit https://github.com/sinricpro/esp8266-esp32-sdk/issuesand check for existing issues or open a new one
*/

// Uncomment the following line to enable serial debug output
//#define ENABLE_DEBUG

#ifdef ENABLE_DEBUG
#define DEBUG_ESP_PORT Serial
#define NODEBUG_WEBSOCKETS
#define NDEBUG
#endif

#include
#ifdef ESP8266
#include
#endif
#ifdef ESP32
#include
#endif

#include "SinricPro.h"
#include "SinricProThermostat.h"

#define WIFI_SSID "YOUR_WIFI_SSID"
#define WIFI_PASS "YOUR_WIFI_PASSWORD"
#define APP_KEY "YOUR_APP_KEY_HERE" // Should look like "de0bxxxx-1x3x-4x3x-ax2x-5dabxxxxxxxx"
#define APP_SECRET "YOUR_APP_SECRET_HERE" // Should look like "5f36xxxx-x3x7-4x3x-xexe-e86724a9xxxx-4c4axxxx-3x3x-x5xe-x9x3-333d65xxxxxx"
#define THERMOSTAT_ID "YOUR_DEVICE_ID_HERE" // Should look like "5dc1564130xxxxxxxxxxxxxx"
#define BAUD_RATE 115200 // Change baudrate to your need

float globalTemperature;
bool globalPowerState;

bool onPowerState(const String &deviceId, bool &state) {
Serial.printf("Thermostat %s turned %s\r\n", deviceId.c_str(), state?"on":"off");
globalPowerState = state;
return true; // request handled properly
}

bool onTargetTemperature(const String &deviceId, float &temperature) {
Serial.printf("Thermostat %s set temperature to %f\r\n", deviceId.c_str(), temperature);
globalTemperature = temperature;
return true;
}

bool onAdjustTargetTemperature(const String & deviceId, float &temperatureDelta) {
globalTemperature += temperatureDelta; // calculate absolut temperature
Serial.printf("Thermostat %s changed temperature about %f to %f", deviceId.c_str(), temperatureDelta, globalTemperature);
temperatureDelta = globalTemperature; // return absolut temperature
return true;
}

bool onThermostatMode(const String &deviceId, String &mode) {
Serial.printf("Thermostat %s set to mode %s\r\n", deviceId.c_str(), mode.c_str());
return true;
}


void setupWiFi() {
Serial.printf("\r\n[Wifi]: Connecting");
WiFi.begin(WIFI_SSID, WIFI_PASS);

while (WiFi.status() != WL_CONNECTED) {
Serial.printf(".");
delay(250);
}
IPAddress localIP = WiFi.localIP();
Serial.printf("connected!\r\n[WiFi]: IP-Address is %d.%d.%d.%d\r\n", localIP[0], localIP[1], localIP[2], localIP[3]);
}

void setupSinricPro() {
SinricProThermostat &myThermostat = SinricPro[THERMOSTAT_ID];
myThermostat.onPowerState(onPowerState);
myThermostat.onTargetTemperature(onTargetTemperature);
myThermostat.onAdjustTargetTemperature(onAdjustTargetTemperature);
myThermostat.onThermostatMode(onThermostatMode);

// setup SinricPro
SinricPro.onConnected([](){ Serial.printf("Connected to SinricPro\r\n"); });
SinricPro.onDisconnected([](){ Serial.printf("Disconnected from SinricPro\r\n"); });
SinricPro.begin(APP_KEY, APP_SECRET);
}

void setup() {
Serial.begin(BAUD_RATE); Serial.printf("\r\n\r\n");
setupWiFi();
setupSinricPro();
}

void loop() {
SinricPro.handle();
}