光伏离网并网逆变器解决方案
本套逆变器方案DC-DC采用Boost升压，DCAC采用单相全桥逆变电路结构。以TI公司的浮点数字信号控制器TMS320F28335DSP为控制电路处理器，采用规则采样法和DSP片内ePWM模块功能实现PWM和SPWM波。PV最大功率点跟踪（MPPT）采用了恒压跟踪法（CVT法）来实现，并用软件锁相环进行系统的同频、同相控制，控制灵活简单。方案本身包含原理图，PCB(Protel打开），源程序代码（CCS打开），BOM清单。
硬件方案底板主要包含各种接口，包括RS232接口，PWM接口，输出并网继电器接口，按键，LCD及开关量输出，RS485接口，LED，JTAG下载接口，CAN总线接口，核心板接口，蜂鸣器以及DAC接口等。2层板，已经覆铜，以下展示部分BOM。
| Comment | Description | Designator |
| SW-PB | Switch | B1, B2, B3, B4 |
| 104 | Capacitor | C1, C2, C3, C4, C6, C10, C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C21, C22, C23, C24, C48 |
| 332 | Capacitor | C25, C26, C27, C28, C29, C30, C31, C32, C33, C34, C35, C36, C37, C38, C39, C40 |
| 105 | Capacitor | C41, C42 |
| 10uF/16V | Bi-Polar Capacitor, Polarized Capacitor (Radial) | C43, C44, C45 |
| 331 | Capacitor | C46, C47 |
| LED | D1, D2, D3, D4, D5 | |
| 1N4007 | Diode | D6 |
| ADCA | Connector | J1 |
| ADCB | Connector | J2 |
| ST7920-12864 | J3 | |
| JUMP | Connector | J4 |
| JQ | Connector | J5 |
| DAC | Connector | J6 |
| POWER | J7 | |
| JUMP | Connector | J10 |
| RS485 | Connector | J11 |
| CAN | Connector | J12 |
| NETCON | J15 | |
| SPI | Connector | J16 |
| COM | Connector | J17 |
| JTAG | Header, 7-Pin, Dual row | JG1 |
| IDC80 | JP1, JP2 | |
| HRS2H-S-DC5V | K1 | |
| 10uH | Inductor | L1, L2, L3 |
| 7SEG | LD1, LD2, LD3 | |
| Bell | Electrical Bell | LS1 |
| RS232_B | Header, 4-Pin | P1 |
| DRIVER | Connector | P2 |
| MMBT2222A | NPN Transistor | Q1, Q2 |
| 102 | R1, R2, R4, R8, R9, R10, R13, R21, R22 | |
| 103 | R3, R5, R6, R7, R11, R12 | |
| 101 | R14, R16, R17 | |
| 201 | R15 | |
| 121 | R18, R19 | |
| 512 | R20 | |
| 0 | R23, R24, R25 | |
| 102*4 | RP1, RP2, RP3, RP4, RP5, RP6 | |
| RS232_A | Receptacle Assembly, 9 Position, Right Angle | RS1 |
| SW-DT | Connector | SW1 |
| LM358 | Fast Settling Dual Operational Amplifier | U1, U2, U3, U4 |
| TLV5620 | U9 | |
| REF3020 | U10 | |
| LM1117-3.3 | U11 | |
| MAX3232A | +5V Powered, Multi-Channel RS-232 Driver/Receiver | U12 |
| MAX485 | U13 | |
| SN65HVD235 | U14 | |
| SN74HC164 | 8-Bit Shift Register with 3-State Output Registers | U15, U16, U17 |
| 74LVXC3245 | U18 |
硬件方案--采样驱动隔离板
采样驱动板包括ACDX SPWM驱动部分，比较器LM393，MOS驱动ICIR2100，光耦6N137，LDO 78M15和78M05。此外还包含输出电压及输出电流检测部分，市电过零比较，直流输入电流检测等功能电路。PCB是2层板，以下展示部分BOM。
| Comment | Description | Designator |
| 470uF/25V | C1 | |
| 470uF/35V | Bi-Polar Capacitor | C3 |
| 104 | [NoValue], Capacitor | C5, C6, C7, C8, C9, C10, C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C21, C22, C23, C24, C25, C26, C27, C28, C51, C52 |
| 10uF/25V | Capacitor | C29, C30, C31, C32, C33, C34, C35, C36, C37, C38 |
| 15p | Capacitor | C39, C40 |
| 47uF/16VD | Polarized Capacitor (Radial) | C41 |
| 103 | [NoValue], Capacitor | C42, C46, C47, C53, C54 |
| 100uF/25V | Bi-Polar Capacitor | C43 |
| 10uF/25VD | Capacitor | C44, C45 |
| 470uF/25V | Bi-Polar Capacitor | C48, C49 |
| 331 | Capacitor | C50 |
| 101 | Capacitor | C55, C56, C57 |
| 332 | Capacitor | C58 |
| LED | D2 | |
| UF4007 | Diode | D3, D4 |
| DC2405D-1W | DC1 | |
| POWER | Connector | J1 |
| 10uH | Inductor | L1, L2 |
| MAIN | Connector | P1 |
| DCAC | Connector | P2 |
| 5H11G | PNP General Purpose Amplifier | Q1 |
| 4H11G | NPN General Purpose Amplifier | Q2 |
| 471 | R1, R2, R3 | |
| 101 | R4, R5, R34 | |
| 100 | R6, R7 | |
| 472 | R8, R9, R33 | |
| 102 | R10, R11, R12, R13, R18 |
硬件方案--逆变板
逆变板主要是高压电路大电流电路，包括MOSFETFSW25N50A，电流传感器ACS712-05B，比较器LM358，光耦HCNR200，EMI及并网电路。PCB是2层板，可以看到基本都是大面积铺铜来实现连通，以下展示部分BOM。
| Comment | Description | Designator |
| 47uF/50V | Electrolytic Capacitor | C1 |
| 100uF/450V | Bi-Polar Capacitor | C2 |
| 105/630V | Capacitor | C3, C4 |
| 104 | [NoValue], Capacitor | C5, C6, C14, C15 |
| 103 | C7, C8 | |
| 102 | Capacitor | C9, C10 |
| 470uF/250V | Bi-Polar Capacitor | C11, C12 |
| 224/630V | Capacitor | C13 |
| 475/630V | C16 | |
| 104/630V | Capacitor, [NoValue] | C17, C18, C21 |
| 472/250V | C19, C20 | |
| MUR1560 | Diode | D1 |
| LED | D2 | |
| 1N4007 | Diode | D3 |
| LED | D4 | |
| 1N4148 | Diode | D5, D6, D7, D8 |
| FUSE | Fuse | F1 |
| JUMP | Connector | JP1, JP3, JP4 |
| PV | Connector | JP2 |
| ACOUT | Connector | JP5 |
| TRA2L-24VDC | K1 | |
| TS | Inductor | KT1 |
| 1mH | Inductor | L1 |
| 2.5mH | Inductor | L2, L3 |
| DCAC | Connector | P1 |
| FSW25N50A | Q1, Q2, Q3, Q4, Q5 | |
| MMBT2222A | NPN Transistor | Q6 |
| 914 | R1, R2 | |
| 10R | R3, R4, R5, R6, R7 | |
| 473 | R8, R9, R10 | |
| 201 | R11 | |
| 330K/1W | R12 |
硬件方案--主控板
主控板主要是主控的最小系统电路，包括了TI的DPS TMS320F28035 80pin的封装，外部512K存储器AT24C512，JTAG下载接口，复位及BOOT电路。PCB是2层板，已经覆铜，以下展示部分BOM。
| Comment | Description | Designator |
| 225 | Capacitor | C1, C2, C3, C4, C5, C6, C7, C8 |
| 104 | Capacitor | C9, C10, C11, C12, C13 |
| 10uF/16V | Polarized Capacitor (Radial) | C14, C17 |
| 22p | Capacitor | C15, C16 |
| LED | D1 | |
| PW | Connector | J1 |
| IDC80 | JP1, JP2 | |
| Header 7X2 | Header, 7-Pin, Dual row | JTAG1 |
| 10uH | L1, L2, L3 | |
| 102 | R1, R2, R3, R4 | |
| 472 | R5 | |
| 222 | R6 | |
| 103 | R7, R8 | |
| 0R | R9, R10 | |
| AT24C512 | U1 | |
| TMS320F28035-80 | U2 | |
| LM1117-3.3 | U3 | |
| 6M | Crystal Oscillator | Y1 |
软件方案
软件是DSP方案，采用规则采样法和DSP片内ePWM模块功能实现PWM和SPWM波。PV最大功率点跟踪（MPPT）采用了恒压跟踪法（CVT法）来实现，并用软件锁相环进行系统的同频、同相控制，控制灵活简单。软件工程用CCS打开。
审核编辑：汤梓红
声明：本文内容及配图由入驻作者撰写或者入驻合作网站授权转载。文章观点仅代表作者本人，不代表德赢Vwin官网
网立场。文章及其配图仅供工程师学习之用，如有内容侵权或者其他违规问题，请联系本站处理。
举报投诉
-
原理图
+关注
关注
1296文章
6338浏览量
233751 -
逆变器
+关注
关注
283文章
4715浏览量
206679 -
光伏
+关注
关注
42文章
2966浏览量
68873 -
DC-DC
+关注
关注
30文章
1943浏览量
81603 -
逆变电路
+关注
关注
19文章
297浏览量
39442
发布评论请先 登录
相关推荐
光伏发电的离网电站和并网电站哪个好？
电站，什么是离网电站，各自有什么好处，才好针对本身的情况去作出明智且利益最大化的选择。 并网电站，顾名思义，就是将光伏电站发出的电量直接连
发表于 01-18 16:08
离网逆变器和并网逆变器的区别与特点
离网逆变器采用模块部件的完整系统解决方案Xantrex XW由一些可管理的构建块组成：XW逆变器/充电器、太阳能充电控制器、自动发电机起动模
发表于 03-01 16:37
•2.6w次阅读
并网逆变器和离网逆变器有什么不同
光伏逆变器最主要的功能是把太阳能电池板所发出的直流电转化成家电使用的交流电，太阳能电池板所发出的电全部都要通过逆变器的处理才能对外输出，而对于光
发表于 05-12 16:55
•7746次阅读
并网逆变器和离网逆变器的区别
光伏逆变器最主要的功能是把太阳能电池板所发出的直流电转化成家电使用的交流电，太阳能电池板所发出的电全部都要通过逆变器的处理才能对外输出，而对于光
工商网监
评论